ASR1000-RP1

ASR1000-RP1 Specification

(Note: The Cisco ASR 1002 chassis comes with the Cisco ASR 1000 Series RP1 built into the chassis.)

(Note: Cisco ASR 1001, ASR 1001-X, and ASR 1002-X (part numbers ASR1001, ASR1001-X, ASR1002-X) have an integrated Route Processor built in to the chassis that is not upgradable)

●  Auxiliary port (RJ-45 connector)

●  10/100/1000 Ethernet port (RJ-45 connector)

●  Two RJ-48 connectors for BITS input clocks

●  Two 2-GB DDR2 mini-DIMMs

●  Upgradable memory from 2-GB to 4-GB DRAM

●  1-GB USB Compact Flash memory

●  BGP RR Scalability up to 5,000,000 IPv4 routes or 3,000,000 IPv6 routes

●  Support for online insertion and removal (OIR)

●  Support for NSF and Stateful Switchover (SSO)

●  Support for ISSU

●  Console port (through the CLI)

●  Simple Network Management Protocol (SNMP)

●  RFC 2665

Green – All power rails are within specifications

●  STAT – Status

Green – Cisco IOS Software has booted

Yellow – BootROM has successfully loaded

Red – System failure or during boot process

●  ACTV- Active

Green – Active route processor

●  STBY – Standby

Yellow – Standby route processor

●  CRIT – Critical

Red – Critical alarm or during boot process

●  MAJ – Major

Red – Major alarm

●  MIN – Minor

Amber – Minor alarm

●  LINK – Management Ethernet link status

Solid green – Link with no activity

FLASH green – Link with activity

Off – No link

●  DISK0 – Internal Compact Flash

FLASH Green – Activity indicator

Off – No activity

●  DISK1 – External Compact Flash
FLASH green – Activity indicator
Off – No activity

●  DISK2 – Internal HDD
FLASH green – Activity indicator
Off – No activity

●  CARRIER – BITS interface
Off – Out of service
Green – In frame and in service
Amber – Fault or loop condition

●  UL60950-1 and CAN/CSA-C22.2 No. 60950-1-03 Information technology equipment

●  AS/NZS 60950-1

●  IEC/EN 60950-1 Information technology equipment

●  73/23/EEC

Electromagnetic Emissions Certification

●  AS/NZ 3548: 1995 (including AMD I + II) Class B

●  EN55022: 1998 Class B

●  CISPR 22: 1997

●  EN55022: 1994 (including AMD I + II)

●  47 CFR Part 15: 2000 (FCC) Class B

●  VCCI V-3/01.4 Class 2

●  CNS-13438: 1997 Class B

●  GR1089: 1997 (including Rev. 1: 1999)

Immunity

●  EN300386: 2000-TNE EMC requirements; product family standard; high priority of service; central office and noncentral office locations

●  EN50082-1: 1992/1997

●  EN50082-2: 1995-Generic Immunity Standard, Heavy

Industrial

●  CISPR24: 1997

●  EN55024: 1998-Generic ITE immunity standard

●  EN61000-4-2: 1995 + AMD I + II ESD, Level 4/8 kV contact, 15 kV air

●  IEC-1000-4-3: 1995 + AMD 1-Radiated Immunity, 10 V/m

●  IEC-1000-4-4: 1995-Electrical Fast Transients, Level 4/4 kV/B

●  IEC-1000-4-5: 1995 + AMD 1-DC Surge-Class 3; AC Surge-Class 4

●  EN61000-4-6: 1996 + AMD 1-RF conducted immunity, 10 Vrms

●  EN61000-4-11: 1995-Voltage Dips and Sags

●  ETS300 132-2: 1996 + corrigendum, December 1996

●  GR1089:1997 (including Rev1: 1999)

Network Equipment Building Standards

The module meets the following Networking Equipment Building Standards (NEBS):

●  GR-1089-CORE

●  GR-63-CORE

European Telecommunication Standards Institute (ETSI)

●  ETSI 300 386-1 – Levels for equipment with a “high priority of service” that is installed in “locations other than telecommunication centers”

●  ETSI 300 386-2:1997 – Levels for equipment with a “high priority of service” that is installed in “locations other than telecommunication centers”

●  ETSI 300 132-2: December 1994 – Power supply interfaces at the input to telecommunications equipment Sections 4.8 and 4.9

●  Operating temperature, nominal: 41 to 104°F (5 to 40°C)

●  Operating temperature, short-term: 23 to 131°F (-5 to 55°C)

●  Storage relative humidity: 5 to 95% relative humidity (RH)

●  Operating humidity, nominal: 5 to 85% RH

●  Operating humidity, short-term: 5 to 90% RH

●  Operating altitude: -60 to 4000m (up to 2000m conforms to IEC/EN/UL/CSA 60950 requirements)