AIR-AP1832I-Q-K9 Specification |
Description | 802.11ac Wave 2 AP, 3×3:2, Internal Antenna, Q Regulatory Domain |
Software | Cisco Unified Wireless Network Software Release with AireOS wireless controllers: - 8.1.121.0 or later for the Cisco Aironet 1830 Series Access Points
|
Deployment modes | Centralized, standalone, sniffer, Cisco FlexConnect™, monitor, OfficeExtend, mesh |
Supported wireless LAN controllers | - Cisco 2500 Series Wireless Controllers, Cisco Wireless Controller Module for ISR G2, Cisco Wireless Services Module 2 (WiSM2) for Cisco Catalyst®6500 Series Switches, Cisco 5500 Series Wireless Controllers, Cisco 5520 Series Wireless Controllers, Cisco Flex® 7500 Series Wireless Controllers, Cisco 8500 Series Wireless Controllers, Cisco 8540 Series Wireless Controllers, Cisco 5760 Wireless LAN Controller, Cisco Catalyst 3650 and 3850 Series Switches with integrated controller
- Cisco Mobility Express
|
802.11n version 2.0 (and related) capabilities | - 3×3 MIMO with two spatial streams
- Maximal ratio combining (MRC)
- 20- and 40-MHz channels
- PHY data rates up to 300 Mbps (40 MHz with 5 GHz)
- Packet aggregation: A-MPDU (Tx/Rx), A-MSDU (Tx/Rx)
- 802.11 dynamic frequency selection (DFS)
- Cyclic shift diversity (CSD) support
|
802.11ac Wave 1 and 2 capabilities | - 3×3 MIMO with two spatial streams, single-user or multiuser MIMO
- MRC
- 802.11ac beamforming (transmit beamforming)
- 20-, 40-, and 80-MHz channels
- PHY data rates up to 867 Mbps (80 MHz in 5 GHz)
- Packet aggregation: A-MPDU (Tx/Rx), A-MSDU (Tx/Rx)
- 802.11 DFS
- CSD support
|
Regulatory Domain | Q (Q regulatory domain): – 2.412 to 2.472 GHz; 13 channels – 5.180 to 5.320 GHz; 8 channels – 5.500 to 5.700 GHz; 11 channels |
Integrated antenna | - 2.4 GHz, gain 3 dBi, internal omni, horizontal beamwidth 360°
- 5 GHz, gain 5 dBi, internal omni, horizontal beamwidth 360°
|
Interfaces | - 1 x 10/100/1000BASE-T autosensing (RJ-45), Power over Ethernet (PoE)
- Management console port (RJ-45)
- USB 2.0 (enabled via future software)
|
Indicators | - Status LED indicates boot loader status, association status, operating status, boot loader warnings, boot loader errors
|
Dimensions (W x L x H) | - Access point (without mounting bracket): 8.3 x 8.3 x 2 in. (210.8 x 210.8 x 50.8 mm)
|
Weight | |
Environmental | Cisco Aironet 1830i - Nonoperating (storage) temperature: -22° to 158°F (-30° to 70°C)
- Nonoperating (storage) altitude test: 25˚C, 15,000 ft.
- Operating temperature: 32° to 104°F (0° to 40°C)
- Operating humidity: 10% to 90% (noncondensing)
- Operating altitude test: 40˚C, 9843 ft.
|
System memory | |
Input power requirements | - AP1830: 44 to 57 VDC
- Power supply and power injector: 100 to 240 VAC; 50 to 60 Hz
|
Power draw | Note: When deployed using a PoE specification, the power drawn from the power sourcing equipment will be higher by some amount, depending on the length of the interconnecting cable. |
Powering options | - 802.3af/802.3at
- Enhanced PoE
- Cisco local power supply, AIR-PWR-C=
- Cisco power injector, AIR-PWRINJ5= (Note:This injector supports 802.3af only), AIR-PWRINJ6=
Note: If 802.3af PoE is the source of power, the USB port is disabled. |
Warranty | Limited lifetime hardware warranty |
