AIR-AP1852E-T-K9 Specifications |
Description | 802.11ac Wave 2 Access Point, 4×4:4, External-Ant, T Regulatory Domain |
Software | Cisco Unified Wireless Network Software Release with AireOS wireless controllers: - 8.1 MR1 or later for the Cisco Aironet 1850 Series Access Points
|
Regulatory Domain | T (T regulatory domain): – 2.412 to 2.462 GHz; 3 channels – 5.280 to 5.320 GHz; 3 channels – 5.500 to 5.700 GHz; 8 channels (excludes 5.600 to 5.640 GHz) – 5.745 to 5.825 GHz; 5 channels |
Deployment modes | Centralized local, Standalone, Sniffer, Cisco FlexConnect, Monitor, OfficeExtend, Mesh |
Supported wireless LAN controllers | - Cisco 2500 Series Wireless Controllers, Cisco Wireless Controller Module for ISR G2, Cisco Wireless Services Module 2 (WiSM2) for Catalyst 6500 Series Switches, Cisco 5500 Series Wireless Controllers, Cisco Flex 7500 Series Wireless Controllers, Cisco 8500 Series Wireless Controllers, Cisco 5760 Series Wireless Controllers, Cisco Catalyst 3650/3850 Series switch with integrated controller
- Cisco Mobility Express
|
802.11n version 2.0 (and related) capabilities | - 4×4 MIMO with four spatial streams
- Maximal ratio combining (MRC)
- 20- and 40-MHz channels
- PHY data rates up to 600 Mbps (40 MHz with 5 GHz)
- Packet aggregation: A-MPDU (Tx/Rx), A-MSDU (Tx/Rx)
- 802.11 dynamic frequency selection (DFS)
- Cyclic shift diversity (CSD) support
|
802.11ac Wave 1 and 2 capabilities | - 4×4 MIMO with four spatial streams, single-user MIMO
- 4×4 MIMO with three spatial streams, multiuser MIMO
- MRC
- 802.11ac beamforming (transmit beamforming)
- 20-, 40-, and 80-MHz channels
- PHY data rates up to 1.7 Gbps (80 MHz in 5 GHz)
- Packet aggregation: A-MPDU (Tx/Rx), A-MSDU (Tx/Rx)
- 802.11 DFS
- CSD support
- Rogue device detection
|
External antenna (sold separately) | - Certified for use with antenna gains up to 6 dBi (2.4 GHz and 5 GHz)
- Cisco offers the industry’s broadest selection of antennas, delivering optimal coverage for a variety of deployment scenarios
|
Interfaces | - 1 x 10/100/1000BASE-T autosensing (RJ-45), Power over Ethernet (PoE)
- 1 x 10/100/1000BASE-T autosensing (RJ-45), AUX (used for Link Aggregation)
- Management console port (RJ-45)
- USB 2.0 (enabled via future software)
|
Indicators | - Status LED indicates boot loader status, association status, operating status, boot loader warnings, boot loader errors
|
Dimensions (W x L x H) | - Access point (without mounting bracket): 8.3 x 8.3 x 2 in. (210.8 x 210.8 x 50.8 mm)
|
Weight | |
Environmental | Cisco Aironet 1850e - Nonoperating (storage) temperature: -22° to 158°F (-30° to 70°C)
- Nonoperating (storage) altitude test: 25˚C, 15,000 ft.
- Operating temperature: -4° to 122°F (-20° to 50°C)
- Operating humidity: 10% to 90% (noncondensing)
- Operating altitude test: 40˚C, 9843 ft.
|
System memory | |
Input power requirements | - AP1850: 44 to 57 VDC
- Power supply and power injector: 100 to 240 VAC; 50 to 60 Hz
|
Power draw | Note: When deployed using a Power over Ethernet (PoE) specification, the power drawn from the power sourcing equipment will be higher by some amount, depending on the length of the interconnecting cable. |
Powering options | - 802.3at
- Enhanced PoE
- Cisco power injector, AIR-PWRINJ4=
- Cisco local power supply, AIR-PWR-C=
- Cisco power injector, AIR-PWRINJ5= (Note: this injector supports 802.3af only)
- 802.3af
Note: If 802.3af PoE is the source of power, (1) the 1852e 2.4-GHz radio will shift to 2×3 from 3×4, (2) The USB port and AUX Ethernet port are disabled on both the 1852i and 1852e. |
Warranty | Limited lifetime hardware warranty |
